A subwoofer connection with your home theater receiver helps you to experience incredible sound quality. It can regenerate and anticipate low frequency sounds well. In fact, it can produce better sound quality than most of the speakers. The subwoofers permit you to actually feel the sound similar to a tremble in your chest.
A video or audio receiver and some speakers are what you need to add a subwoofer connection to your home theater or TV. So, you should join your subwoofer to the receiver with utmost importance to get the best audio quality. You can simply connect them using the speaker wires you already have. Here, in this article, we will describe to you how to connect a subwoofer to a receiver using speaker wires.
- New twisted flare port contributes to clear and tight bass
- Advanced YST II (Yamaha Active Servo Technology II)
- 10” cone woofer
Step 1 –
First of all, organize your speakers and their cables. Don’t connect them to any other device. The step is called ‘blocking’. This procedure is essential to advance your speaker placement. Besides, you can position them without extending wires or moving your furnishings, etc.
Step 2 –
Now, set the subwoofer at the center position of your home theater. The sound provided by the subwoofers is omnidirectional in nature. So, you’ll have same audio results wherever you place it in your room. Apart from placing them in the middle, you may place it in front of the TV or home theater. You just need to ensure that the subwoofer is close to your receiver.
However, if you place your subwoofer adjacent to the walls, it will intensify the bass and so it will be hard for you to control it.
Step 3 –
Keep the speakers on both sides of your theater. Make sure to place the ‘left’ speaker on the left side and the ‘right’ one to the right side as per the manual guideline. The distance between both of the speakers should be the same from each side of your TV.
Now, angle each speaker slightly, so it faces straight to the center of your room’s seating corner. Let’s move to the next step.
Step 4 –
After setting the speakers properly, you should proceed to place the receiver in the right place. You should place it in a place near to both your TV and the power source. So, you can plug the receiver into both of them sufficiently.
However, keep in mind to locate your receiver in a place where it can adequately release the heat produced. So, never set it in a closed cabinet.
Step 5 –
Extend wire from the speaker to your receiver. Try to cover the remaining portions of the wire while joining them to the receiver. Otherwise, someone may trip over the cable accidentally and pull out your speakers.
If possible, move the wires throughout the wall or beneath the carpet. Moreover, cut some slacks at every closure, so the connections there won’t be pushed.
Step 6 –
Let’s associate all the speakers to one another. Interface one side of the speaker wire to the rear part of one speaker, and then join that speaker to a further speaker in the queue. You have to set all of the speakers in a line throughout the whole room from one front speaker to the other one.
Don’t interface the front via the speaker wires. Connect them using AV cables.
Step 7 –
Now, connect your subwoofer to the receiver with speaker wires. Interface the subwoofer to the subwoofer port on your receiver. The port is often labeled as ‘sub out’.
Step 8 –
Plug in the receiver in a power source. Once you’ve plugged the receiver, it will switch on slowly. However, it may spend quite a few minutes to start completely, as this is your first time to set up this kind of connection.
Step 9 –
Finally, connect the whole assembly to your TV or home theater or any other system. Then, check out the surround audio quality. Every theater system has a unique pattern of audio configuration. But, you can change this configuration as per your preferences. For changing this, click the ‘menu’ button of your remote, then select ‘audio’, and finally set the default sound options.
Enjoy the best quality sound system from your media source with a subwoofer. Connect the subwoofer and receiver like a professional on your own. Follow these simple steps and surely you will be able to connect the subwoofer to your receiver with ease.